Enertherm

Enertherm

FLAT ROOF INSULATION

enertherm-alu-245x300IKO enertherm is used for the thermal insulation of flat roofs.

IKO enertherm ALU
IKO enertherm BGF
IKO enertherm MG


BENEFITS:

  • Lightweight boards and therefore easier to handle.
  • Less volume for the same insulation value.
  • Fit for walking on during the work and after.
  • Can be installed quickly and easily.
  • High dimensional stability and compressive strength.


IKO enertherm ALU

ALU

IKO enertherm ALU is a 100 % CFC, HCFC or HFC-free insulation board with a rigid polyisocyanurate foam core, clad on both sides with a multi-layer gastight aluminium complex. This high-quality reflecting ALU cladding consists of no fewer than seven layers, combined into a single complex. It is tested under extreme conditions in respect of water absorption, mechanical properties, corrosion resistance and emissivity.

RANGE OF APPLICATIONS

Rooftop: flat roof insulation for timber, concrete and steel deck.

Sarking: pitched roof insulation (type nF with neutral felt).

Floor: floor insulation (underfloor heating and concrete floors).

Wall: cavity wall insulation.

Wrap: outside wall insulation (closed joints).

Comfort: loft insulation.

TECHNICAL APPROVALS

TECHNICAL APPROVALS: Europe: CE – EN 13165: T2-DS(70,90)3-DS(-20,-)1-DLT(2)-TR80-CS(10Y)150-WL(T)1

Belgium: ATG 2726 – ATG 2727 – ATG H867

France: Certificat Acermi N° 06/103/434 DTA 5/13-2350

Netherlands: Komo Attest met Productiecertificaat CTG 485 Komo CTG 544

Germany: Bauaufsichtliche Zulassung Z 23.15-161

USA: FM Factory Mutual

FIRE PROPERTIES

– Fire class according to EN 13501-1: Class E

– Fire class ‘end use’ according to 13501-1: B-s2,d0 (steeldeck)

– Fire class according to KB 19/12/1997: A1 (Belgium)

IKO enertherm BGF

enertherm-bgf-245x300IKO enertherm BGF is a 100 % CFC, HCFC or HFC-free insulation board with a rigid polyisocyanurate foam core, clad on both sides with a polypropylene-covered bitumen sand and tallow-free glass membrane.

RANGE OF APPLICATIONS

Rooftop: flat roof insulation

TECHNICAL APPROVALS

Europe: CE markering – EN 13165: T2-DS(70,90)3-DS (-20,-)1-DLT(2)5-TR80-CS(10Y)150-WL(T)1

Belgium: ATG 2726

Netherlands: Komo CTG 485

Germany: Bauaufsichtliche Zulassung Z 23.15-161

FIRE PROPERTIES

– Fire class according to EN 13501-1: Class F

IKO enertherm MG

IKO enertherm MG is a 100 % CFC, HCFC or HFC-free insulation board with a rigid polyisocyanurate foam core, clad on both sides with a perforated coated glass membrane

RANGE OF APPLICATIONS

enertherm-mg-245x300RANGE OF APPLICATIONS: Rooftop: flat roof insulation in combination with plastic membranes

TECHNICAL APPROVALS

Europe: CE markering – EN 13165: T2-DS(70,90)3-DS (-20,-)1-DLT(2)5-TR80-CS(10Y)150-WL(T)1

Belgium: ATG 2726 – ATG H867

Netherlands: Komo CTG 485

Germany: Bauaufsichtliche Zulassung Z 23.15-161

FIRE PROPERTIES

– Fire class according to EN 13501-1: Class E

LOFT INSULATION

IKO enertherm comfort is the perfect loft insulation solution based on the extremely thin IKO enertherm ALU board. The following insulation board is applicable: IKO enertherm ALU TG

BENEFITS:

  • No additional vapour screen needed thanks to closed cell structure of the board and seams taped with IKO ALU tape.
  • Various finishes possible: plasterboard, laths, etc.
  • Very quick installation thanks to convenient size and light weight.
  • Moisture-insensitive and non-deformable.

IKO enertherm ALU TG

IKO enertherm ALU is a 100 % CFC, HCFC or HFC-free insulation board with a rigid polyisocyanurate foam core, clad on both sides with a multi-layer gastight aluminium complex. This high-quality reflecting ALU cladding consists of no fewer than seven layers, combined into a single complex. It is tested under extreme conditions in respect of water absorption, mechanical properties, corrosion resistance and emissivity.

RANGE OF APPLICATIONS

Rooftop: flat roof insulation for timber, concrete and steel deck.

Sarking: pitched roof insulation (type nF with neutral felt).

Floor: floor insulation (underfloor heating and concrete floors).

Wall: cavity wall insulation.

Wrap: outside wall insulation (closed joints).

Comfort: loft insulation.

TECHNICAL APPROVALS

Europe: CE – EN 13165: T2-DS(70,90)3-DS(-20,-)1-DLT(2)-TR80-CS(10Y)150-WL(T)1 Belgium: ATG 2726 – ATG 2727 – ATG H867 France: Certificat Acermi N° 06/103/434 DTA 5/13-2350 Netherlands: Komo Attest met Productiecertificaat CTG 485 Komo CTG 544

Germany: Bauaufsichtliche Zulassung Z 23.15-161

USA: FM Factory Mutual

FIRE PROPERTIES

– Fire class according to EN 13501-1: Class E – Fire class ‘end use’ according to 13501-1: B-s2,d0 (steeldeck) – Fire class according to KB 19/12/1997: A1 (Belgium)

PITCHED ROOF INSULATION WITH UNDERTILE FELT

IKO enertherm is used for the thermal insulation of pitched roofs on the rafters or on the trusses. The following insulation board is applicable: IKO enertherm ALU NF PRO

3d-sarking-pro-317x176BENEFITS:

  • Insulation shield on the trusses without breaks.
  • The IKO enertherm ALU NF PRO board comes with integrated vapour-permeable undertile felt.
  • Integrated vapour-permeable undertile felt provided with a double adhesive strip.
  • Interior finish and volume are retained.
  • Windproof in one operation.
  • Very low loading of the roof structure thanks to the light weight.
  • Very easy installation without breaks.


LOFT FLOOR INSULATION

3d-zolder-317x176IKO enertherm is used for the insulation of the loft floor.

The following insulation board is applicable: IKO enertherm ALU TG

BENEFITS:

  • Fast and reliable insulation solution.
  • No structural works.
  • Inexpensive system.
  • Loose installation in combination with OSB boards.
  • The tongue and groove connection of the boards provides for a single insulation shield.
IKO enertherm ALU is a 100 % CFC, HCFC or HFC-free insulation board with a rigid polyisocyanurate foam core, clad on both sides with a multi-layer gastight aluminium complex. This high-quality reflecting ALU cladding consists of no fewer than seven layers, combined into a single complex. It is tested under extreme conditions in respect of water absorption, mechanical properties, corrosion resistance and emissivity.

RANGE OF APPLICATIONS

Rooftop: flat roof insulation for timber, concrete and steel deck.

Sarking: pitched roof insulation (type nF with neutral felt).

Floor: floor insulation (underfloor heating and concrete floors).

Wall: cavity wall insulation.

Wrap: outside wall insulation (closed joints).

Comfort: loft insulation.

TECHNICAL APPROVALS

Europe: CE – EN 13165: T2-DS(70,90)3-DS(-20,-)1-DLT(2)-TR80-CS(10Y)150-WL(T)1

Belgium: ATG 2726 – ATG 2727 – ATG H867

France: Certificat Acermi N° 06/103/434 DTA 5/13-2350

Netherlands: Komo Attest met Productiecertificaat CTG 485 Komo CTG 544

Germany: Bauaufsichtliche Zulassung Z 23.15-161

USA: FM Factory Mutual

FIRE PROPERTIES

– Fire class according to EN 13501-1: Class E

– Fire class ‘end use’ according to 13501-1: B-s2,d0 (steeldeck)

– Fire class according to KB 19/12/1997: A1 (Belgium)

CAVITY WALL INSULATION

spouwmuur-3d1-317x176IKO enertherm is used for the thermal insulation of cavity walls. The following insulation board is applicable:

IKO enertherm ALU TG

BENEFITS:

  • The dimensional stability of the boards guarantees one unbroken insulation shield.
  • The outstanding thermal performance of IKO enertherm means that one thin insulation board in the cavity is enough.
  • Quick and easy to cut and install.
  • The tongue and groove connection avoids thermal bridging and ingress of water.
  • The lightweight board facilitates transport and installation.
  • The ALU cladding is corrosion-resistant.
  • Fibre-free board, so no irritation.
IKO enertherm ALU is a 100 % CFC, HCFC or HFC-free insulation board with a rigid polyisocyanurate foam core, clad on both sides with a multi-layer gastight aluminium complex. This high-quality reflecting ALU cladding consists of no fewer than seven layers, combined into a single complex. It is tested under extreme conditions in respect of water absorption, mechanical properties, corrosion resistance and emissivity.

RANGE OF APPLICATIONS

Rooftop: flat roof insulation for timber, concrete and steel deck.

Sarking: pitched roof insulation (type nF with neutral felt).

Floor: floor insulation (underfloor heating and concrete floors).

Wall: cavity wall insulation.

Wrap: outside wall insulation (closed joints).

Comfort: loft insulation.

TECHNICAL APPROVALS

Europe: CE – EN 13165: T2-DS(70,90)3-DS(-20,-)1-DLT(2)-TR80-CS(10Y)150-WL(T)1

Belgium: ATG 2726 – ATG 2727 – ATG H867

France: Certificat Acermi N° 06/103/434 DTA 5/13-2350

Netherlands: Komo Attest met Productiecertificaat CTG 485 Komo CTG 544

Germany: Bauaufsichtliche Zulassung Z 23.15-161

USA: FM Factory Mutual

FIRE PROPERTIES

– Fire class according to EN 13501-1: Class E
– Fire class ‘end use’ according to 13501-1: B-s2,d0 (steeldeck)
– Fire class according to KB 19/12/1997: A1 (Belgium)

OUTSIDE WALL INSULATION

iko-enertherm-wrap-3d-317x176IKO enertherm is the solution for the insulation of outside walls. The following insulation boards are applicable:

IKO enertherm ALU
IKO enertherm ALU 50

BENEFITS:

  • Interior finish of the home is retained.
  • Various decorative finishes possible: timber, zinc, sidings, etc.
  • Nearly 40 % thinner than mineral wool, XPS or EPS with the same R value.
  • Wind and moisture-proof insulation shield.
  • Can be cut and installed quickly and easily.
  • The ALU cladding is corrosion-resistant.

IKO enertherm ALU

IKO enertherm ALU is a 100 % CFC, HCFC or HFC-free insulation board with a rigid polyisocyanurate foam core, clad on both sides with a multi-layer gastight aluminium complex. This high-quality reflecting ALU cladding consists of no fewer than seven layers, combined into a single complex. It is tested under extreme conditions in respect of water absorption, mechanical properties, corrosion resistance and emissivity.

RANGE OF APPLICATIONS

Rooftop: flat roof insulation for timber, concrete and steel deck.

Sarking: pitched roof insulation (type nF with neutral felt).

Floor: floor insulation (underfloor heating and concrete floors).

Wall: cavity wall insulation.

Wrap: outside wall insulation (closed joints).

Comfort: loft insulation.

TECHNICAL APPROVALS

Europe: CE – EN 13165: T2-DS(70,90)3-DS(-20,-)1-DLT(2)-TR80-CS(10Y)150-WL(T)1

Belgium: ATG 2726 – ATG 2727 – ATG H867

France: Certificat Acermi N° 06/103/434 DTA 5/13-2350

Netherlands: Komo Attest met Productiecertificaat CTG 485 Komo CTG 544

Germany: Bauaufsichtliche Zulassung Z 23.15-161

USA: FM Factory Mutual

FIRE PROPERTIES

– Fire class according to EN 13501-1: Class E

– Fire class ‘end use’ according to 13501-1: B-s2,d0 (steeldeck)

– Fire class according to KB 19/12/1997: A1 (Belgium)

IKO enertherm ALU 50

IKO enertherm ALU 50 is a 100 % CFC, HCFC or HFC-free insulation board with a rigid polyisocyanurate enertherm-alu-50-245x300foam core, clad on both sides with a 50 μm unmarked gastight aluminium layer.

RANGE OF APPLICATIONS

Wrap: outside wall insulation

Rooftop: flat roof insulation

Sarking: pitched roof insulation

Base: basement insulation

TECHNICAL APPROVALS

Europe: CE markering – EN 13165: T2-DS(70,90)3-DS (-20,-)1-DLT(2)5-TR80-CS(10Y)150-WL(T)1

Belgium: ATG H867

France: Certificat Acermi N° 12/03/800

Germany: Bauaufsichtliche Zulassung Z 23.15-161

FIRE PROPERTIES

– Reaction to fire according to EN 13501-1: Class D-s2, d0

– Reaction to fire “end use” according to EN 13501-1: Class B-s1, d0

– Reaction to fire according to KB 19/12/1997: A1 (Belgium)

FLOOR INSULATION

3d-vloer-317x176IKO enertherm is used for the thermal insulation of floors. The following insulation board is applicable:

IKO enertherm KR ALU TG

BENEFITS:
  • Exceptional dimensional and compressive stability.
  • With grid as reference for underfloor heating.
  • Moisture-insensitive and rot-proof.
  • Very light and above all convenient size.
  • Very easy to process.
  • SFast installation with tongue and groove connection.
IKO enertherm ALU is a 100 % CFC, HCFC or HFC-free insulation board with a rigid polyisocyanurate foam core, clad on both sides with a multi-layer gastight aluminium complex.

RANGE OF APPLICATIONS

Floor: floor insulation (underfloor heating and concrete floors)

Wall: industrial applications

TECHNICAL APPROVALS

Europe: CE markering – EN 13165: T2-DS(70,90)3-DS (-20,-)1-DLT(2)5-TR80-CS(10Y)150-WL(T)1

France: Certificat Acermi N° 06/103/436

FIRE PROPERTIES

– Fire class according to EN 13501-1: Class F

BASEMENT INSULATION

IKO enertherm is used for the insulation of underground spaces and basements. The following insulation board is applicable:

IKO enertherm ALU 50 TG

3d-kelder-317x176BENEFITS:
  • Lightweight board for easy installation.
  • With tongue and groove system for perfect connection.
  • Fast processing.
  • Installation using concrete screws and cover plates.
  • The aluminium cladding can be coated for a uniform white finish.
IKO enertherm ALU 50 is a 100 % CFC, HCFC or HFC-free insulation board with a rigid polyisocyanurate foam core, clad on both sides with a 50 μm unmarked gastight aluminium layer.

RANGE OF APPLICATIONS

Wrap: outside wall insulation

Rooftop: flat roof insulation

Sarking: pitched roof insulation

Base: basement insulation

TECHNICAL APPROVALS

Europe: CE markering – EN 13165: T2-DS(70,90)3-DS (-20,-)1-DLT(2)5-TR80-CS(10Y)150-WL(T)1

Belgium: ATG H867

France: Certificat Acermi N° 12/03/800

Germany: Bauaufsichtliche Zulassung Z 23.15-161

FIRE PROPERTIES

– Reaction to fire according to EN 13501-1: Class D-s2, d0

– Reaction to fire “end use” according to EN 13501-1: Class B-s1, d0

– Reaction to fire according to KB 19/12/1997: A1 (Belgium)

TOP
Chat with us
Chat with us
Questions, doubts, issues? We're here to help you!
Connecting...
None of our operators are available at the moment. Please, try again later.
Our operators are busy. Please try again later
Have you got question? Write to us!
:
:
This chat session has ended